Recent Changes

Thursday, August 24

  1. page Akebono Wheel Clearance edited ... Yes Good clearance in all directions. Enkei RPF1 18" 10.5 +15 Yes {Capture.PNG} …
    ...
    Yes
    Good clearance in all directions.
    Enkei RPF1
    18"
    10.5
    +15
    Yes
    {Capture.PNG}

    Rears
    Rears aren't usually an issue, but problem wheels will be added here.
    (view changes)
    4:01 pm
  2. file Capture.PNG uploaded
    4:01 pm

Tuesday, June 6

  1. page ECU Harness Diagram edited The diagram below illustrates (in fantastic detail) the ECCS wiring diagram in the Z32. Thanks to …
    The diagram below illustrates (in fantastic detail) the ECCS wiring diagram in the Z32.
    Thanks to Lee Wood (tt.net: leezeedoesit) for creating this!
    {ECCS_colored_m.gif}
    Related Articles
    Electronic Fuel Injection (Category)
    (view changes)
    9:35 am
  2. page ECU Harness Diagram edited The diagram below illustrates (in fantastic detail) the ECCS wiring diagram in the Z32. Thanks to …
    The diagram below illustrates (in fantastic detail) the ECCS wiring diagram in the Z32.
    Thanks to Lee Wood (tt.net: leezeedoesit) for creating this!
    {ECCS_colored_m.gif} Click for full-size.
    Related Articles
    Electronic Fuel Injection (Category)
    (view changes)
    9:35 am
  3. 9:34 am

Monday, June 5

  1. msg ECU relocation message posted ECU relocation Hello im am thinking of relocating my ecu to the old battery spot in the engine bay just wanted to …
    ECU relocation
    Hello im am thinking of relocating my ecu to the old battery spot in the engine bay just wanted to know if it would be possible and what all i would have to do in order for it to connect and have everything inside the car work
    1:48 pm

Tuesday, April 4

  1. page Throttle Position Sensor edited ... Reading the voltage across the inserted wire from the Position Sensor section, ensure the volt…
    ...
    Reading the voltage across the inserted wire from the Position Sensor section, ensure the voltage is between 0.4V and 0.5V.
    If any adjustments are made to get the position switch into the correct voltage range, repeat step 2 to ensure the hard idle switch is still showing ON with the throttle closed.
    If you're unable to get the TPS voltage and hard idle switch to their "sweet spot," try this:
    Rotate the TPS so that the TPS voltage is reading between 0.4 to 0.5v.
    Unplug the gray oval TPS connector for several seconds. You should be able to see the voltage (as displayed via consult) rise. After about ~8 seconds, the hard idle switch should display "on"
    Reconnect the gray oval TPS connector.

    For your TPS to be set correctly, the following conditions must all be simultaneously true.
    The throttle bodies should be closed all the way. Removing the intake pipes allows you to see if they are completely closed. With the throttle closed, you should be able to see a port (one on each throttle) on the bottom of the throttle chamber. These ports lead to vacuum nipples on the undersides of the throttle chambers. If the butterfly valve is slightly open, it usually obscures the ports.
    (view changes)
    2:13 pm

Monday, February 20

  1. page Akebono Wheel Clearance edited ... Nismo LMGT4 18" 9.5" 8.5" +25 Yes ... Rears aren't usually an issue, b…
    ...
    Nismo LMGT4
    18"
    9.5"8.5"
    +25
    Yes
    ...
    Rears aren't usually an issue, but problem wheels will be added here.
    Template Test Fitting
    ...
    the spoke.
    {G35AkBBKTestFit-Front.jpg}
    Related Articles
    (view changes)
    10:55 am

More